tic216 series silicon triacs
1 december 1971 - revised september 2002 specifications are subject to change without notice. sensitive gate triacs 6 a rms glass passivated wafer 400 v to 800 v off-state voltage max i gt of 5 ma (quadrants 1 - 3) absolute maximum ratings over operating case temperature (unless otherwise noted) notes: 1. these values apply bidirectionally for any value of resistance between the gate and main terminal 1. 2. this value applies for 50-hz full-sine-wave operation with resistive load. above 70c derate linearly to 110c case temperatu re at the rate of 150 ma/c. 3. this value applies for one 50-hz full-sine-wave when the device is operating at (or below) the rated value of on-state current. surge may be repeated after the device has returned to origi nal thermal equilibrium. during the surge, gate control may be lost. 4. this value applies for a maxi mum averaging time of 20 ms. rating symbol value unit repetitive peak off-state voltage (see note 1) TIC216D tic216m tic216s tic216n v drm 400 600 700 800 v full-cycle rms on-state current at (or below) 70c case temperature (see note 2) i t(rms) 6 a peak on-state surge current full-sine-waveat (or below) 25c case temperature (see note 3) i tsm 60 a peak gate current i gm 1 a peak gate power dissipation at (or below) 85c case temperature (pulse width 200 s) p gm 2.2 w average gate power dissipat ion at (or below) 85c case temperat ure (see note 4) p g(av) 0.9 w operating case temperature range t c -40 to +110 c storage temperature range t stg -40 to +125 c lead temperature 1.6 mm from case for 10 seconds t l 230 c electrical characteristics at 25c case tem perature (un less otherwise noted ) parameter test conditions min typ max unit i drm repetitive peak off-state current v d = rated v drm i g = 0 t c = 110c 2 ma i gt gate trigger current v supply = +12 v? v supply = +12 v? v supply = -12 v? v supply = -12 v? r l = 10 ? r l = 10 ? r l = 10 ? r l = 10 ? t p(g) > 20 s t p(g) > 20 s t p(g) > 20 s t p(g) > 20 s 5 -5 -5 10 ma ? all voltages are with respect to main terminal 1. mt1 mt2 g to-220 package (top view) pin 2 is in electrical contact with the mounting base. mdc2aca 1 2 3
tic216 series silicon triacs 2
december 1971 - revised september 2002 specifications are subject to change without notice. ? all voltages are with respect to main terminal 1. notes: 5. this parameter must be measured using pulse techniques, t p = 1 ms, duty cycle 2 %. voltage-sensing contacts separate from the current carrying contacts are located within 3.2 mm from the device body. 6. the triacs are triggered by a 15-v (open-circuit amplitude) pulse supplied by a generator with the following characteristics: r g = 100 ? , t p(g) = 20 s, t r = 15 ns, f = 1 khz. v gt gate trigger voltage v supply = +12 v? v supply = +12 v? v supply = -12 v? v supply = -12 v? r l = 10 ? r l = 10 ? r l = 10 ? r l = 10 ? t p(g) > 20 s t p(g) > 20 s t p(g) > 20 s t p(g) > 20 s 2.2 -2.2 -2.2 3 v v t on-state voltage i t = 8.4 a i g = 50 ma (see note 5) 1.7 v i h holding current v supply = +12 v? v supply = -12 v? i g = 0 i g = 0 init? i tm = 100 ma init? i tm = -100 ma 30 -30 ma i l latching current v supply = +12 v? v supply = -12 v? (see note 6) 4 -2 ma dv/dt critical rate of rise of off-state voltage v drm = rated v drm i g = 0 t c = 110c 20 v/s dv/dt (c) critical rise of commutation voltage v drm = rated v drm i trm = 8.4 a t c = 70c 2 5 v/s thermal characteristics parameter min typ max unit r jc junction to case thermal resistance 2.5 c/w r ja junction to free air thermal resist ance 62.5 c/w electrical characteristics at 25c case temperature (unless otherwise noted) (continued) parameter test conditions min typ max unit
tic216 series silicon triacs 3
december 1971 - revised september 2002 specifications are subject to change without notice. to-220 3-pin plastic flange-mount package this single-in-line package consists of a circuit mounted on a lead frame and encapsulated within a plastic compound. the compound w ill withstand soldering te mperature with no defor mation, and circuit performance characteristics will remain stable when operated in high humidity conditions. leads require no additional cleaning or proces sing when used in soldered assembly. mechanical data to-220 all linear dimensions in millimeters ? 1,23 1,32 4,20 4,70 123 0,97 0,66 10,0 10,4 2,54 2,95 6,0 6,6 14,55 15,32 12,7 14,1 5,6 6,1 1,07 1,47 2,34 2,74 4,68 5,28 3,71 3,96 0,41 0,64 2,40 2,90 n ote a: the centre pin is in electr ical contact with the mounting tab. 18,0 typ.
|
